How To Install A Toilet Seat – The Best Guide And Tips 2023

How to install a toilet seat? The process of replacing a toilet seat is fast and simple. If you are able to change a toilet seat, you can create a stylish enhancement in your bathroom within time. Seats can become damaged or damaged however, the main objective is to improve the appearance of the bathroom. The replacement of a toilet seat could be the easiest bathroom fix to do since there is no need to shut off your water.

Toilet seats are available in two designs or sizes that are circular (16 inches across from the front and back) and oblong, also known as extended (18 inches back to front). Make sure to measure the old seat before you shop to ensure that you purchase the right size.

For replacing the toilet seat You’ll require a screwdriver, a wrench that can be adjusted, and obviously the new seat.

Are All Toilets Exactly The Same?

Are All Toilets Exactly The Same?

There is a difference between toilet seats that will fit as toilets are available in a variety of different designs that’s why you’ll have to confirm your toilet before purchasing.

There are three different toilet designs that are commonly seen inside UK homes. They are D-shape, round or round seats. Another very popular option is a soft-close seat which is why if you are looking for this type of seat, you must measure your toilet to ensure that this kind of seat is suitable for your toilet.

The seats of toilets that can be replaced may be adjusted to accommodate toilets with non-standard or older designs but the seat needs to be supported by the hinges or contact points.

Most toilet seats have oval in shape, but certain models may have a modern shape, such as a square shape or D-shape. It is therefore important to be aware of this when looking for a replacement at an outlet or from the manufacturer that made the original.

Do I have to Take any Security Measures Before Changing the Seat in my Bathroom?

Toilets are the perfect place for germs that can cause harm and could be the source of infection so you should be aware of the dangers prior to starting.

Wear gloves made of rubber whenever changing the toilet seat. Ideally, clean it prior to getting rid of it. After you’ve removed the seat and cleaned the toilet, give it an extensive cleaning. Apply an antibacterial spray available at many stores.

Make sure you wash your hands with antibacterial soap after you’ve changed the toilet seat to ensure you’ve got rid of all harmful germs.

So, How to Install a Toilet Seat?

1. Choosing a New Seat

  1. Check the dimensions of your toilet bowl prior to purchasing an entirely brand new toilet seat. Most toilets are normal-sized, so any replacement seat will be able to fit. If you’d like to be certain, you can use an instrument to measure the distance between bolt holes inside your toilet bowl. Also, ensure that the bolts’ distance on the new seat is exactly the same.
  2. Select the type of seat you’d like. Toilet seats come in two basic designs, and a home supply store will have many brands to choose from. The most common type is round and you can pick an elongated version should you prefer. It is also possible to purchase a “whisper near” seat with special pads at the bottom to stop it from hitting the bowl.
    • Toilet seats are available at various costs. You’ll be able to locate the most affordable cost of $20-30, while there are those that are priced twice or more.
  3. Choose a seat color that complements your toilet. You can find toilet seats in a range of shades. Select one that complements the bowl of your toilet (usually white) for a traditional look or opt for a more striking hue to make an even bold statement. You could, for instance, opt for a wooden or blue toilet seat that contrasts with a white toilet bowl.
  4. Get your tools ready to complete your task. You’ll need just two basic tools to tackle this task. If you don’t have these tools at your home, go to the hardware store to purchase:
    • Pliers or adjustable wrench
    • A flat-head screwdriver
    • Spray oil like WD-40 (optional)
    • An inexpensive hacksaw (optional)

2. Removing the Old Toilet Seat

Use a screwdriver for popping the plastic caps of the bolts.

Utilize the wrench adjustable to hold the nut that is located underneath the bolt for the seat.

Turn the seat bolts using the screwdriver. After you’ve removed the nuts, remove the seat.

Pull the anchor bolts from your new seat into the hole, then manually tighten the nuts.

The bolt holes should be aligned of the new seat to the holes in the base of the toilet. Insert the anchor bolts into the holes, then screw the nuts onto the side of the bolts, until hand tight. Then, you can center the seat and make sure the bolts are tightened.

After the seat has been centered and the seat is centered, use the adjustable wrench for tightening the nuts. Don’t force the nuts too tight — just enough to make them snug is sufficient.

3. Installing the New Seat

  1. Set the new seat up. Remove it from the box. The hinges of the seat will be attached. Install them exactly where the hinges from the previous seat were.
    • The box may also include locks and bolts. They may also have plastic caps made that cover the bolts. Install this hardware on the side.
  2. The bolts should be dropped in the appropriate. Take a bolt in your palm. There will be holes in the hinge that allow bolts to be put into. Because the seat of your toilet is located exactly where the old seat was, the holes will be placed right on top of the holes that are on top of the bowl. The bolts should be dropped over the hole in hinges and the bowl with the bolt’s head sitting on the top.
    • Don’t worry. Because the bolts are fitted with an end, they won’t fall to the bottom of the holes.
  3. The nuts are threaded onto bolts. Pick up one of the nuts. Take a look at the other edge of the bathroom bowl. There should be an end bolt hanging down from over the edge inside the bowl. Make sure you turn the nut over the bolt (clockwise) until it is as tight as you are able to do it manually. Make use of an adjustable wrench, to loosen the bolt a little more.
    • Repeat the process with the second nut on the opposite end of the toilet.
    • If the device you purchased has washers, put washers on the threads of bolts before putting them on the nuts.
    • If the hinges are fitted with bolt caps made of plastic (or when they’re included in the packaging along with the toilet seat) you can snap them into the right position by pressing them against the head of the bolts when you’re finished.
  4. The seat snaps into its place, or else. For some models of toilet seats, you do not push the bolts into the hinges. Instead, you lower bolts directly into the holes that are on both sides of the bowl, and not drive them through the hinges before. Once they are in place, you can fix them by using nuts. The hinges on the seat will snap on or slide overhead bolts.
    • Make sure you read the directions on the back of the toilet seat if you have this model.

Step-By-Step Guide On How To Replace a Toilet Seat

Do you have a small toilet for your small areas? Perhaps you’d like to work on a bidet seat for your toilet. No matter what model you want to change, follow these steps to modify any model.

Step 1: Measure Your Toilet Seat

Measure Your Toilet Seat

Start by understanding the measurements of your current toilet bowl. Since most bowls have the same dimensions, a brand new one is the best alternative. To come up with a great concept, you can place a tape ruler in between bolts in the toilet and then note the length.

Check next to see if your bolts for the seat are of the same measurements.

Step 2: Pick A Style And Color Of Your New Toilet Seat

Visit your local shop and pick the best toilet seat. Typically, the item is available in two varieties namely either a round or an elongated version. If you’re looking for something unique, opt for quiet seats that have special pads.

When you go to the store there is an ideal seat that fits your budget. They can be just $20. However, if you have the cash to spend it’s possible to choose more costly choices.

Before you decide on the best way to replace a toilet cover Choose one with colors that are similar to the one you have. If you are unsure choose white to create a timeless appearance. To create a unique look you can try putting an upholstered or blue seat on a white bathroom.

Step 3: Set Out The Needed Tools

As we mentioned, changing an old chair requires the use of a few tools. The tools include a screwdriver with a flat head as well as an adjustable wrench and spray oil.

It is also possible to use a small hacksaw and two pliers. If you don’t have the tools, visit a hardware shop.

Step 4: Take Out The Current Seat

Take Out The Current Seat

Remove the caps from the bolts and pull them out. Begin by looking at the top of the seat, then look for the location close to the tank. There are caps of plastic on either end of your bowl.

Put the screwdriver in the cap and then pull. However, if the bowl isn’t using caps the hinges will be stocked with bolts.

Choose your adjustable wrench, and then take the nuts. They are the ones that are used to hold the bolts just below the edges of the bowl. Take the nuts off using the help of a wrench using counterclockwise motions.

Remove the bolts from the hinges at the upper part of the bowl. This is where you’ll need to use the screwdriver especially when they have slotted heads. If not, turn the nuts (and washers) until they fall off. In both cases, you can use clockwise movements.

The bolts may feel stuck in particular on older toilets. It is, however, possible to take them out even if dirt or rust clings to them. Apply WD-40 onto the bolts and remove in 10 to 15 minutes.

Are you still stuck with a nut? Make sure to keep it in place using the wrench and turn the nut by using a screwdriver (with your second hand). If the bolts were still stuck, you can employ a hacksaw to remove them. To do this, place the blade in the nut and then cut it by gliding motions.

Once loose, remove your toilet’s bolts. Then, remove the hinges and seat. Then, you can try to throw things that are old into the garbage.

Step 5: Prepare To Install The New Toilet Seat

Remove the seat from the box. The seat is pre-attached hinges that you put on top of the hinges that were previously seat attached. Additionally, you will find bolts, nuts, and plastic covers within the box.

Find the bolt holes in the seat hinges and select the bolt and secure it into the hole by placing the head at the highest point. When you do this the bolt is not able to be removed from the hole.

Step 6: Fix The Nuts Into The Bolts

Fix The Nuts Into The Bolts

Examine one side of your toilet to see that are bolts sticking out of its top. After that, screw the screw and nut (with clockwise motions) on one of these bolts. It is possible to utilize your hands for this work before tightening some using the wrench.

Then, move to the opposite end of the bowl, and repeat the process for the bolt. If the new seat has washers, make sure they are fixed prior to installing the nuts. Then, put the caps made of plastic (if supplied) over the bolts and press them hard.

How Do You Install a New Toilet Seat

After you’ve taken down your old seat, it’s now time to put in the new one. There will be fittings included in the new toilet seat with instructions from their manufacturer about how you can put them together. the fittings.

In essence, fitting a brand new toilet seat is the opposite of the removal.

Then, you need to line up and connect the new fittings by slotting the bolts into the holes in the toilet to fix them. Be sure your seat sits in a uniform position around the outside of the toilet bowl, and then center it. Utilize the hands of your partner or for securing the wingnuts when you’re pleased with the position of your seat.

Take care not to tighten too much the bolts as you might need to tighten them up once your new seat has been installed. Also, bolts made of plastic in the event that this is the case – won’t require much pressure before they give way or snap.

There are also rubber washers that you can place between the toilet and the nut in order to create an additional cushion.

This will be done across both seats since there are two bolts and two wingnuts that will be tightened into their place.

If plastic caps were supplied in the new toilet seat fix them by pressing them down the bolts and then onto the wingscrews.

If you adhere to these steps, you will be able to change the toilet seat fast and effortlessly.

Step 7: Attach The Toilet Seat On The Bowl

If you are learning to replace the toilet seat It is possible you won’t need to drive bolts through hinges, except for certain models. In these toilets, insert an anchor into the hole, then screw it into the bolt. After that, the hinges of the seat slide over the upper plastic bolts.

If you do know how to take off hinges on your toilet seat it is recommended to read the instruction manual included in the package of the new seat.

How Do you Determine the Size of a Toilet Seat?

This is perhaps the most crucial aspect of changing your toilet seat. You aren’t going to want to purchase one that doesn’t work.

Are Toilet Seats of Normal Size?

There’s no universal size that fits all toilets because of the variety of toilet designs. To determine the most suitable seats for the toilet you have, you’ll have to determine the size of your toilet. Learn how to measure your toilet.

There are some key measurements you’ll need regardless of whether the toilets are adjustable to accommodate the standard toilet bowl sizes. The dimensions are:

  • It is the distance that lies between holes for fixing in which the screw holes. It is usually an average measurement of 155mm. However, it’s important to check
  • The length that the bathroom bowl is at its largest point.
  • The length of the bowl from the back of the bowl to the seat-fixing holes

With these measurements, you will be certain that you are buying the right size toilet seat.

Toilet Seat Designs

Whatever the size and style of your bathroom, you’re certain to find the perfect toilet seat to fit your needs. It is available in a variety of sizes and shapes and a variety of colors ranging from traditional white to sparkling pink or even a seat with an exquisite animal style there’s an option for everyone’s preference.

When Should I Change The Seat On My Toilet?

When Should I Change The Seat On My Toilet?

A broken or damaged toilet seat is just one of the most obvious reasons to consider a replacement. Additionally, if your bathroom is a bit shaky it is advisable to consider buying an entirely new one. You can also replace the seat you have been using, especially when you want a fresh style.

While it’s not common there are bathrooms constructed recently that come with water closets that do not have seats. If this is the case it is important to be aware of how to replace the toilet seat.

Important Safety Tips For Replacing Toilet Seat

Since water closets deal with the disposal of waste, they serve as the perfect habitat for harmful microorganisms. Before you begin working on one, make use of the following guidelines.

Don’t change the seat using only your hands. Instead, put on gloves made of rubber. These items can be purchased from your local shop at a reasonable price.

Clean the seat prior to taking it out of the bowl. Clean the entire toilet prior to placing the new toilet seat. To clean the toilet completely you can use an anti-bacterial cleanser.

Look also – 6 The Best Comfortable Toilet Seat Reviews 2022

Wrap Up

Seats are changed due to a variety of reasons. Although the process may seem complicated, however, it’s quite simple. It’s also possible to complete the job without making an email to your plumber and asking “how much it will cost to replace the toilet seat?”

Begin by measuring the distance between your existing seat and the seat. Use this to find a replacement one. Select the seat that is in line with the design as well as the color and style of your bathroom. Make sure you have the right tools to put the new seat back in the closet.

Make sure you are wearing gloves when performing the task. It is also recommended to make use of a cleaner to clean it off before replacing it.

I hope that you enjoyed this post. Please share this article with your contacts on social media and post any feedback below.


Is Installing A Toilet Seat Easy?

The installation of new seats for your toilet is an easy and quick task. It doesn’t matter if you want to replace your old, broken toilet seat or you want to make your bathroom a more modern appearance with a brand new knowing how to put in the toilet seat is just an issue of following the steps in a couple of easy steps.

Do all toilet seats fit all toilets?

There is a difference. Not all toilet seats are made to be the same as toilets are available in a range of shapes. Therefore, you’ll need to know your shape of yours before purchasing. There are three kinds of toilet shapes that are common within UK homes. They are D-shape, round, and square.

How Do You Put A Toilet Seat On For Dummies?

For replacing the seat of your toilet you’ll need a screwdriver and adaptable wrench and obviously, the new seat.
1. Pry to open bolt cap. …
2. Put the nut in underneath the bolt. …
3. Take off the seat bolts and lift the seat. …
4. The anchor bolts of this seat in the slots, then hold the nuts in place.

About Post Author

Leave a Comment